The cold brittleness risk of automobile control cables in low temperature areas is mainly manifested in the decline of the physical properties of the material. Especially in extremely low temperature conditions, the insulation and sheath materials of the cable will become hardened and brittle, and thus be prone to cracking when subjected to slight external force or mechanical stress, resulting in safety hazards such as short circuit or leakage. In addition, low temperatures can also lead to a decrease in the flexibility of cables, increasing the difficulty of laying and maintenance, and may even cause the risk of breakage.
I. The Impact of Low Temperature on Control Cables
Material embrittlement
In low-temperature environments, the insulation and sheath materials of cables (such as PVC, XLPE, rubber, etc.) will lose their flexibility and exhibit brittle characteristics. This embrittlement can cause the cable to develop cracks when subjected to mechanical stress or bending, thereby affecting its mechanical and electrical properties.
2. Decline in insulation performance
Low temperatures not only harden the cable materials but may also lead to a decrease in insulation resistance, changes in capacitance and dielectric loss, thereby affecting the electrical performance of the cables. At extremely low temperatures, the insulating layer may experience stress concentration due to contraction, increasing the risk of breakdown or short circuit.
3. Changes in the resistance of conductors
In a low-temperature environment, the resistance of conductors may decrease, which may have a positive impact on transmission efficiency, but at the same time, it also poses higher requirements for the thermal management of the system. If the resistance of the conductor is too low, it may cause local overheating and accelerate the aging of the insulation layer.
4. The difficulty of laying and maintenance increases
Low temperatures make cables stiff and difficult to bend, requiring greater traction force and easily damaging the insulation layer and sheath. In addition, if there is no compensation for thermal expansion and contraction after installation, the cable may shift due to temperature changes or tension changes, resulting in damage to the insulation layer.
Ii. Protective Measures for Control Cables in Low-temperature Areas
1. Material selection
Choosing cable materials suitable for low-temperature environments is the key. Commonly used cold-resistant materials include:
- Cold-resistant PVC sheath: It can still maintain a certain degree of flexibility at low temperatures.
Nitrile composite sheath: It has excellent cold resistance and mechanical strength.
Silicone rubber or fluoropolymers: Maintain flexibility and durability in extremely cold environments.
Adding plasticizers or fabric softeners: For instance, adding 3 to 5 parts of powdered nitrile rubber to PVC materials can effectively improve their low-temperature performance.
2. Preheating treatment
Preheating treatment should be carried out before laying cables in a low-temperature environment. The preheating time is usually 2 to 3 minutes to enhance the flexibility of the cable and reduce the risk of cracking. After preheating, the laying should be completed as soon as possible to prevent the cable from hardening again at low temperatures.
3. Precautions for construction and installation
- Choose a period with higher temperatures for construction: Avoid laying cables at low temperatures. If construction must be carried out at low temperatures, it should be done during a period with higher temperatures.
- Avoid excessive bending and stretching: Under low-temperature conditions, the bending radius of the cable should be appropriately increased to reduce the force applied.
- Use protective layers: Lay protective layers (such as fabric, foam, etc.) in the cable trench to prevent the cables from directly touching the ground or sharp objects.
- Handle with care: During transportation and installation, handle with care to avoid collision and dropping to prevent damage to the cables.
4. Storage and Transportation
- Indoor storage: Cables should be stored indoors, avoiding direct contact with the ground or damp environments to prevent freezing and moisture.
- Use sealed equipment: During transportation, sealed equipment should be used to prevent the cables from coming into direct contact with cold air. Use soft pads for protection, handle with care, and avoid excessive bending.
5. Regular inspection and maintenance
Infrared thermal imaging detection: By detecting local hotspots of cables through infrared thermal imaging, potential problems can be identified in a timely manner.
X-ray or ultrasonic testing: Used to detect interlayer delamination and cracks in cables to ensure the integrity of the cables.
- Strengthen daily inspections: Especially in winter, focus on checking for cracks in the insulation layer and loose joints of cables, and conduct regular insulation resistance and dielectric loss tests.
6. Environmental control
- Insulation of the distribution room: Ensure that the temperature in the distribution room or distribution cabinet meets the design requirements to prevent electrical equipment from failing to operate normally due to low temperatures.
- Avoid ice layer adhesion: Under conditions of high air humidity and temperatures close to 0℃, floating ice on conductors may cause damage to towers and a decline in insulator performance. Measures should be taken to prevent ice layer adhesion.
Iii. Summary
The cold brittleness risk of automobile control cables in low-temperature regions mainly stems from the decline in physical properties of the material and the concentration of mechanical stress. To effectively address this issue, comprehensive protective measures should be taken from multiple aspects such as material selection, preheating treatment, construction and installation, storage and transportation, regular inspection and environmental control to ensure the safe operation of cables in low-temperature environments.



